Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Your Plumbing Crash Course: What You Must Have for Installing a Bathtub
Blog Article
We've encountered the article involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround listed below on the net and decided it made perfect sense to discuss it with you on this page.
Setting up a tub isn't exactly brain surgery, but it does call for solid plumbing, carpentry, as well as sometimes, tiling skills. Changing an old tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently available, the project can move rapidly; if you have to open up a wall surface to get rid of the old tub and also place the brand-new bath tub, the task is much harder. In either instance, the job is within a house handyman's abilities, although you will require an assistant to move out the old bathtub as well as set in the new one. Ensure you have actually certified on your own for the work and are comfortable attempting it. As opposed to employing a service provider to take over a halfway-completed project, it is far better to consider utilizing one before you start. Possibilities are you may require an expert plumber to make tube connections.
This post will assist you install a brand-new tub in your washroom if you have actually already purchased a brand-new tub as well as don't require to change the arrangement of your previous supply of water pipes.
Your devices and also material checklist need to make up the following:
Preparing for the Installment
To start with, the supporting frame supplied with the bath needs to be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to avoid stress on the tub.
Fit the versatile faucet adapters to the bottom of both faucets utilizing 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you utilize every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be suited its final setting.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installment, then the first thing you must do is detach the water supply. After doing so, switch on the faucets to drain pipes any kind of water remaining in the system. The procedure of removing the existing faucets can be quite problematic as a result of the limited access that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the staying water that will come from the pipelines. When the supply pipelines have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Before moving on to fit the new faucets, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bath tub
Utilizing the two wooden boards under its feet, place the bath tub in the required setting. The wooden boards are valuable in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto 4 tiny points.
The following goal is to ensure that the bathtub is leveled all round. This can be attained by inspecting the level and adjusting the feet on the bathtub till the spirit level reviews level.
To set up faucets, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; after that do the exact same for the various other faucet.
Switch on the water system as well as check all joints and new pipework for leaks as well as tighten them if needed. Load the bathtub and additionally examine the overflow outlet and the normal outlet for leakages.
Finally, take care of the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the tub should wait up until the bathtub has been used a minimum of when as this will certainly resolve it into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipelines.
If you need to fit a monobloc, then you will need reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin making sure that the washers are in place in between the faucet and also the sink. Secure the tap in position with the manufacturer offered backnut. Once the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind needs to be attached to the faucet finishes initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack an inflexible seal, creating the water to pass through the wall surface between the bathroom as well as the tiling, bring about complications with wetness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your components and also fittings. They are marketed in tubes as well as cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before securing, to allow for the motion experienced when the tub is in use. The sealant can split relatively early if you do not consider this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently available on the marketplace. It is suggested to fit the tiles using water-resistant or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading about Installing A Bathtub? Create a review down the page. We'd be glad to find out your views about this blog post. We are looking forward that you visit us again soon. Appreciated our entry? Please share it. Help other people find it. Many thanks for your time. Come back soon.
Trusted for emergency plumbing excellence. Report this page